HARD TO FIND DRIVERS: May 2009

Sunday, May 24, 2009

SONY VAIO VGN N330N WindowsXP drivers

WindowsXP drivers pack

http://www.easy-share.com/1905349964/SONY VAIO VGN N330N.rar

If have problem installing Windows XP check the ASUS X53 posts. There are some tips that can be used.

Fujitsu Siemens Esprimo V5535 WindowsXP driver

Drivers for windowsXP 32-bits

http://www.easy-share.com/1905349408/FSC ESPRIMO V5535.part1.rar
http://www.easy-share.com/1905349472/FSC ESPRIMO V5535.part2.rar
http://www.easy-share.com/1905349480/FSC ESPRIMO V5535.part3.rar

If have problem installing Windows XP check the ASUS X53 posts. There are some tips that can be used.

Thursday, May 14, 2009

ASUS X53S Windows XPdrivers and tips to install

1. If you try to install Windows XP, you get the: “Setup did not find any hard disk drives” message at the first stage of installing Windows XP.

2. There are no drivers on the official website of asus. The model X53Sg is not even available there. A cd with only Vista drivers was available with the notebook, so I decided to post a guide on how to install XP and all of the drivers for winXP which I found through the net. They are all working perfectly, but they are not available on the asus website.

SOLUTION

1. Passing “Setup did not find any hard disk drives” message on Windows XP Installation
The first thing you have to do is set SATA Mode to Compatible in your BIOS. You should enter the BIOS hitting the F2 key right after the notebook is started. Just navigate to the Advanced tab with your arrow keys, press Enter to the first option IDE Configuration to open it, and then again press enter to the first option SATA Operation Mode to change it to Compatible. If you want to leave SATA mode to enhanced, you can install windows by attaching an USB Floppy Device, and by inserting a previously made floppy with the intel sata drivers for xp, or you could try to slipstream the drivers into Windows XP and install. But I personally wouldn’t go through that much of a pain, because I haven’t noticed any difference between the two modes of SATA.

2 Install XP drivers

http://www.easy-share.com/1905181556/atk0100.rar
http://www.easy-share.com/1905181565/audio.rar
http://www.easy-share.com/1905181575/bluetooth.zip
http://www.easy-share.com/1905181576/cardreader.rar
http://www.easy-share.com/1905181599/chipset.rar
http://www.easy-share.com/1905181601/modem.rar
http://www.easy-share.com/1905181661/vga.rar
http://www.easy-share.com/1905181666/wireless_lan.rar
http://www.easy-share.com/1906218219/L1_2.4.7.11.exe
http://www.easy-share.com/1906218225/jmicro - sata.zip

FOR THE ATI DRIVER check http://www.driverheaven.net/modtool.php ... great tool and tutorial. Work 100%

The JMicro sata driver must need to be instaled manualy.

Another method of installing Xp on this model is to use nLite to create a WindowsXp boot disk in wich to integrate s-ata driver. This method work great with other models of laptops and desktop pc, but this method has some failures, you need to know the exact s-ata chip in order to integrate the driver and get rid of “Setup did not find any hard disk drives”. For this method it is beter to use a CD-RW to burn the image created by nLite, you may not succed for the first time.
I dont use anymore the method with nLite , but I there are laptops that can`t be install either.

To use nLite download below links

http://www.easy-share.com/1905181901/nLite-1.4.rc2.installer.exe
http://www.easy-share.com/1905181903/dotNetFx35setup.exe
http://www.easy-share.com/1905181905/nLite-1.4.5.b2.installer.exe

Wednesday, May 13, 2009

AMI BIOS tool

Great tool for setting AMI BIOS

http://www.easy-share.com/1905163400/tool_8_RC1.rar

Works with ami version below 7.5

Drivers for DELL STUDIO 1735

Reset CANON PIXMA MP160

How to clear E27 Waste ink absorber full
1.With the printer powered off but connected to a power source,
press the Power button while pressing and holding the Stop/ Reset button.
2.When the Power is lit, press the Stop/Reset button two times
while pressing and holding the Power button.
3.When releasing the Power button and the Stop / Reset button (regardless of order),
the printer will move into a service mode. (Waiting for menu selection)
4.When the on/off lights in green, press the Stop/Reset button the
specified number of time(s) according to the function listed in the table below.
(Each time the Stop/Reset button is pressed, the LED lights alternately in orange
and green, starting with orange.)note: press 4 times for waste ink counter reset.5.Turn off the printer.( it must be turn off) then turn it on again.

The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print (auto teste)
2 times Green EEPROM print (dados da EEPROM)
3 times Orange EEPROM reset (EEPROM reset)
4 times Green Waste ink counter reset (Absorvente reset)

NOTE! May work with other MFC printer like MP180

Reset CANON PIXMA IP5000 printer

To reset the counter or to find out about it´s reading you have to use the service mode.
Turn off the printer, push the resume button and keep on pushing.
Press the power button and keep on pushing. Now let go off the resume button,
but not the power button. Push the resume button twice, then let go off all buttons.
You are now in service mode.

To leave the service mode, give the power button one push.

Push the resume button once, after that the power button once.
The first information page appears.
Push reume twice, then power once: You get the second page.

Newer PIXMA-printers print the first page as a test for the nozzles.
The second page contains a lot of information.

Our advice: Print the second page before and after reset of the waste ink counter.
Only then can you be sure that the reset was a success.

To reset the waste ink counter right now, push resume four times and after that power once.

Important: Before starting with normal printing again, switch off the printer.
That gets you out of service mode.

Then switch on the printer again and print as you like.

I think this procedure may work on IP4000/3000 or newer models

Canon Waste Ink Tank Reset Procedures

Canon GENERIC "S" SERIES RESET CODE

Waste Ink Counter Reset.

(1) Turn off the printer.

(2) Press and hold the RESUME button, then press and hold the POWER button.

(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in

succession. Note: you are still holding the POWER button). The printer's carriage will "reset"

or move momentarily. If the above was properly performed the printer will enter the

"Service Mode".

(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp

will alternate (change) color with each key press.

1. Service/Factory test printout, including ink sensor check.

2. EEPROM - Info printout.

3. EEPROM - Initialization.

4. Reset the Waste ink counter.

5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)

After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.

++++++++++

Canon i320, i255

Waste Ink Counter Reset.

Step 1 : Manual for service mode

1. Unplug power and USB.

2. Open door and hold power button.

3. Connect power.

4. Close door, then release power button.

or Step 1: Manual for service mode

1. Turn off the printer. And disconnect the printer cable.

2. Press and hold the POWER button, turn on the printer.

3. The indicator (L.E.D.) should be green.

4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.

5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.

6. Release both buttons.

step 2 : Software for Permanant

1. Reconnect the printer cable.

2.Open General Tools software and select (USB PORT)

3 .Choose (SET DESTINATION 1) And it should be reset.

Remark "After service mode Pls use software for permanent reset"

++++++++++

Canon PIXMA iP1000

Waste Ink Counter Reset.

Step 1: Manual for Service mode

1. Unplug power and USB.

2. Open door and hold power button.

3. Connect power.

4. Close door, then release power button.

step 2 : Software for Permanant

1. Reconnect the printer cable.

2.Open General Tools software and select (USB PORT)

3 .Choose (SET DESTINATION 1) And it should be reset.

Remark "After service mode Pls use software for permanent reset"

++++++++++

Canon PIXMA iP1500

Waste Ink Counter Reset.

Step 1: Manual for Service mode

1. Unplug power and USB.

2. Open door and hold power button.

3. Connect power.

4. Close door, then release power button.

step 2 : Software for Permanant

1. Reconnect the printer cable.

2.Open General Tools software and select (USB PORT)

3 .Choose (SET DESTINATION 1) And it should be reset.

Remark "After service mode Pls use software for permanent reset"

++++++++++

Canon i850, i950, S600

Start with the printer OFF

1. Hold down RESUME and then hold down POWER

2. release RESUME

3. press RESUME twice, then release POWER

4. Let green light blink until printer is done futzing

Select function with RESUME press POWER to execute:

presses - light color - function

Number of presses - light color - function

0 presses - green - Test print (or exit service mode on i960)

1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)

2 presses - green - EEPROM initialize

3 presses - orange - Reset waste ink counter

++++++++++

Canon S450 Printer

1: Power off printer

2: Hold Resume button then press and hold POWER, the beeper will sound once.

3: Hold POWER and release RESUME

4: Press RESUME twice

5. Release Power button

6: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.

7: Press Power to set data

++++++++++

Canon BJC 1000 Serie

1: Remove Cartridge

2: Unplug the AC Power Cord

3: Hold down the RESUME button

4: Release RESUME after plugging in the AC Power cord.

5: Press the RESUME once within 5 seconds and release the RESUME .

6: Press and HOLD RESUME for two seconds or more and release it.

7: Press and HOLD RESUME for two seconds or more and release it.

8: Unplug AC Power Cord to set data.

++++++++++

Canon BJC-2000 BJC-2100 Serie

1: Remove the Cartridge

2: Unplug the AC Power Cord

3: Close Front access panel

3: Hold down the RESUME/RESET button and plug in the AC power cord

4: Release RESUME/RESET after plugging in the AC Power cord.

5: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .

6: Press and HOLD RESUME/RESET for two seconds or more and release it.

7: Press and HOLD RESUME/RESET for two seconds or more and release it.

8: Unplug AC Power Cord to set data.

++++++++++

Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265

Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650

Unplug Power Cord

Hold POWER and RESUME buttons

Plug in Power Cord

Release buttons

Open front door of printer

Hold the CARTRIDGE and RESUME buttons

Press POWER

Release all buttons after the beeps

Press CARTRIDGE once

Press RESUME

++++++++++

Canon BJC-5000

1: Power off printer

2: Press and hold RESUME then press POWER, The indicator will start blinking.

3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode

5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.

6: Press Power to set data

Service Test Print

1: Power off printer

2: Press and hold RESUME then press POWER, The indicator will start blinking.

3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode

5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.

6: Press Power to Print

Nozzle Print

1: Power off printer

2: Press and POWER, until the printer beeps and release.

Demonstration Print

1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.

++++++++++

Canon BJC-5100

Self Test

Switch Printer off. Hold Power for 1 beep.

Waste Counter Reset

1: Power off printer

2: Press and hold RESUME then press POWER, The indicator will start blinking.

3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode

5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.

6: Press Power to set data

Service Test Print

1: Power off printer

2: Press and hold RESUME then press POWER, The indicator will start blinking.

3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode

5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.

6: Press Power to Print

Nozzle Print

1: Power off printer

2: Press and POWER, until the printer beeps and release.

Demonstration Print

1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.

++++++++++

Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620

Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500

1: Power off printer

2: Hold Resume button then press and hold POWER, the beeper will sound once.

3: Hold POWER and release RESUME

4: Press RESUME twice

5: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.

6: Press Power to set data

++++++++++

Canon BJC-600 BJC-600e BJC-610 BJC-620

1: Unplug Power Cord

2: Hold POWER and FF and Print Mode buttons

3: Plug in Power Cord

4: Release after the beeps

++++++++++

Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70

1: Unplug Power Cord

2: Hold POWER and RESUME buttons

3: Plug in Power Cord

4: Release buttons after the printers starts up

5: Hold CARTRIDGE and RESUME

6: Press POWER

7: Release all buttons after the beeps

8: Press CARTRIDGE 16 times

9: Press RESUME

10: Unplug the Power cord

++++++++++

Canon BJ-30 BJC-35v BJC-70

F14 Error Reset

1: Unplug adapter

2: Hold POWER

3: Plug in ADAPTER

4: Release POWER after printer starts

5: Hold FF and MENU and press POWER

6: Release after beeps

7: Press <> Cartridge until 1A is displayed

8: Press ONLINE

9: Press POWER to shutoff printer

10: Unplug printer then re-plug printer

++++++++++

Canon BJ F900, F890, F700, F500, S900, S820, S750 and S520

Turn off the printer.

Press and hold the RESUME button, then press and hold the POWER button.

Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.

You are now in Service mode.

Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.

1. service/factory test printout, including ink sensor check

2. EEPROM info printout

3. EEPROM initialization

4. Clear the waste-ink counter

5. Printer model setting. (more selections beyond this- leave this alone)

After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a resta

++++++++++

Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA iP3000 above,

1. Turn off printer

2. Hold down Resume button and press Power button.

3. Keep holding down Power button and let Resume button go.

4. Press Resume button 2 times then let BOTH buttons go.

5. Green lights will flash and then stop blinking.

6. When green lights are solid, press the Resume button 4 times.

7. Press the Power button and the printer should turn off, if not, press the Power button once more.

8. Your printer should respond as normal.

+++++++++

Canon S900, S820, S750, S520

Turn off the printer.

Press and hold the RESUME button, then press and hold the POWER button.

While still holding the POWER button, Release the RESUME button, then press and release the RESUME button two more times in succession.

The printer mechanics will move momentarily. You are now in Service mode. Release the Power Button.

Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. Service/factory test printout, including ink sensor check

2. EEPROM info printout

3. EEPROM initialization

4. Clear the waste-ink counter

5. Printer model setting. (more selections beyond this- leave this alone)

After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart.

++++++++++

Canon S9000

Turn off printer

Hold down Resume button and press Power button.

Keep holding down Power button and let Resume button go.

Press Resume button 2 times then let BOTH buttons go.

Green lights will flash and then stop blinking.

When green lights are solid, press the Resume button 4 times.

Press the Power button and the printer should turn off, if not, press the Power button once more.

Your printer should respond as normal.

+++++++++

Canon MPC190

Reset Waste Ink

1) Enter SERVICE MODE.

By pressing Menu, Copy, Scan, Copy, Copy

2) Select TEST MODE.

3) Select [8] PRINTER TEST in TEST MODE.

4) Select 3. [EEPROM CLEAR].

5) Select 0. [INK COUNT].

6) Press the [Set] key.

7) Press the [Stop/Reset] key (returnin;g to the state of 3)), and then press the [ON/OFF] key.